Back to Blog
How-to Guides 2026-11-20 Aftermarket Car Parts -Private Label Mfg 0 views

PLM AWD K-Swap Header: K24 K20 Install Tips

PLM AWD K-Swap Header: K24 K20 Install Tips

Install tips for the PLM Power Driven K-Swap AWD Header on K24/K20 AWD builds. What the catalog confirms and what you should check before bolting it on.

What the PLM AWD K-Swap Header Is Designed For

The PLM Power Driven K-Swap K20/K24 AWD Header is built specifically for AWD K-Series swapped vehicles. Developed and tested in-house at PLM using their shop-built AWD EK Civic with a K24 engine, this header addresses the tight packaging and unique drivetrain layout of an AWD K-Swap. Released in August 2026, it's a focused part for enthusiasts who have already committed to the swap and need a header that clears the front axles and transfer case without sacrificing flow.

What the Catalog Confirms About This Header

  • PLM Power Driven K-Swap K24 K20 K-Series AWD Header: Developed and tested in-house at PLM using our shop-built AWD EK Civic with a K24 engine. Confirms the header was designed around a real AWD K-Swap, not adapted from a FWD design. This means fitment issues like axle clearance and steering shaft interference were addressed during development.
    PLM Power Driven K-Swap K24 K20 K-Series AWD Header
    PLM Power Driven K-Swap K24 K20 K-Series AWD Header
  • PLM Power Driven K-Swap K24 K20 K-Series AWD Header: Designed to deliver strong exhaust flow and power while accommodating the unique drivetrain and packaging requirements of an AWD K-Swap. The header is engineered for both performance and clearance, so you don't have to choose between making power and fitting the part.
  • PLM Power Driven K-Swap K24 K20 K-Series AWD Header: Built by enthusiasts, tested on our own car, and proven in-house at PLM. The part has real-world validation, not just theoretical design. This reduces the risk of first-fit surprises.

Key Install Checkpoints Before You Start

Before lifting the car, verify these points against your specific swap. The catalog confirms the header fits an AWD EK Civic with a K24 engine, but your chassis, subframe, and drivetrain may differ.

  • Vehicle and engine combination: The header was developed on an AWD EK Civic with a K24. If your AWD swap uses a different chassis (e.g., CRX, EG, DC2) or a K20 block, check that the ports and flange match your cylinder head. The catalog does not list every compatible chassis.
  • Clearance around the front axles and transfer case: Because the header is designed for AWD, it should clear the front axles and transfer case on the test vehicle. If your swap uses non-standard axle placement or a different transfer case, test fit the header before final assembly.
  • Steering shaft and subframe interference: AWD K-Swap headers often run close to the steering shaft or subframe. The PLM header was tested in a real car, so it likely avoids these on the EK platform, but verify with your specific subframe and steering rack position.
  • O2 sensor and wiring routing: The header likely includes a bung for the wideband O2 sensor. Plan the sensor location and wiring path so it doesn't contact the axle or exhaust heat shield. No specific sensor position is listed in the catalog, so check the header physically.

Installation Steps (Supported by Catalog Evidence)

The catalog does not supply a step-by-step installation procedure, so the following steps are based on typical K-Swap header installation practice. Always refer to the product instructions if included with your shipment.

  1. 1. Prepare the vehicle: Jack the car securely and support the subframe if needed. Remove any exhaust components that interfere with header access. On an AWD swap, this may include the downpipe, catalytic converter, and front exhaust section.
  2. 2. Remove the old header or exhaust manifold: Unbolt the existing header from the cylinder head and exhaust system. Note the gasket condition – replace it if damaged. The PLM header uses standard K-Series port spacing, so a new OEM or aftermarket gasket is recommended.
  3. 3. Test fit the PLM header: Before applying gasket sealant or tightening, place the header against the head. Check clearance around the front axles, transfer case, steering shaft, and subframe. Rotate the crankshaft by hand to ensure the primary tubes don't contact the block or oil pan.
  4. 4. Install the header with a new gasket: Apply the new gasket to the cylinder head studs, then position the PLM header. Tighten the nuts in a crisscross pattern to the manufacturer's torque spec (not supplied in the catalog; use the spec for your K20 or K24 head studs).
  5. 5. Connect the exhaust system: Attach the downpipe or exhaust system to the header collector. Use a new gasket at the collector flange. Ensure the exhaust system doesn't put stress on the header – use a flexible hanger or support if needed.
  6. 6. Final checks and start-up: Reinstall any removed heat shields, wiring, or sensors. Start the engine and check for exhaust leaks at the head flange and collector. Let the engine reach operating temperature and re-torque the header nuts if the gasket compresses.

What the Catalog Does Not Tell You

The catalog does not include a torque specification for the header bolts, a recommended gasket type, or specific O2 sensor bung location. It also does not list every compatible vehicle platform beyond the EK Civic test car. For these details, inspect the header physically and consult your engine's service manual. The header is a performance part, so expect to do some fitment tuning – it's not a direct OEM replacement.

Related Articles

Customer Service
Home
Products
Cart
Profile