What this mid pipe is and is not
The PLM Subaru 2015+ WRX & STi Mid Pipe – Non-Resonated Pipe Only (part # PLM-SUB-MID-2015-2-NON) is a straight pipe section that replaces the resonated portion of a PLM WRX Mid Pipe Kit. It is not a complete exhaust system. It does not include or bolt to the OEM Y-pipe, and it is designed only for those who already have the PLM resonated kit and want to switch to a non-resonated setup.
This guide assumes you have the PLM resonated mid pipe kit installed and are swapping only the resonated section for this non-resonated pipe. If you need the whole mid pipe kit, you will need to source that separately.
What the catalog confirms about this part
- PLM Subaru 2015+ WRX & STi Mid Pipe - Non-Resonated Pipe Only: This is only part of the mid-pipe — the non-resonated (straight pipe) section. Confirms you cannot use this as a standalone mid pipe replacement; it is a conversion piece for an existing PLM kit.

PLM Subaru 2015+ WRX & STi Mid Pipe - Non-Resonated Pipe Only - PLM Subaru 2015+ WRX & STi Mid Pipe - Non-Resonated Pipe Only: Does not include or bolt to OEM Y-Pipe. You must retain your PLM Y-pipe or purchase it separately if your kit did not include one.
- PLM Subaru 2015+ WRX & STi Mid Pipe - Non-Resonated Pipe Only: Installation note: We can only guarantee to fit PLM brand, and we do not accept returns if you try to fit this to another brand, etc. This pipe is designed exclusively for PLM systems. Attempting to adapt it to another brand may cause fitment issues and is not supported.
Installation steps
The following steps describe the general process for swapping the resonated section for the non-resonated pipe on a 2015+ Subaru WRX or STi with a PLM mid pipe kit. Always consult the full instructions that came with your kit for torque specs and specific hardware details.
- 1. Prepare the vehicle: Park on a level surface, apply the parking brake, and chock the rear wheels. Allow the exhaust to cool completely if the vehicle has been running. Raise the rear of the car securely on jack stands.
- 2. Locate the resonated section: Under the car, identify the resonated portion of the PLM mid pipe kit. It is the section with a resonator (a cylindrical chamber) between the front pipe and the Y-pipe.
- 3. Remove the resonated section: Use a penetrating lubricant on the bolts and clamps connecting the resonated section to the front pipe and the Y-pipe. Remove the bolts and slide the resonated section out. Note the orientation of any gaskets or donut seals.
- 4. Install the non-resonated pipe: Position the PLM non-resonated pipe (part # PLM-SUB-MID-2015-2-NON) in place of the resonated section. Ensure the flanges align and that the pipe does not contact the chassis, heat shields, or driveline. Hand-tighten the bolts.
- 5. Tighten all fasteners: Torque the bolts to the manufacturer's specification for your PLM kit. Recheck all clamps and confirm the pipe is securely fastened and does not move when shaken.
- 6. Inspect for clearance and leaks: Lower the vehicle and start the engine. Listen for any exhaust leaks at the joints. Check that the pipe does not vibrate against the underbody. A non-resonated pipe will produce a louder, more aggressive exhaust note.
Fitment checkpoints before you buy
Before ordering, verify that your current setup uses a PLM mid pipe kit. This pipe is not a universal part and will not fit OEM exhausts or other aftermarket brands. Confirm that your PLM kit includes the Y-pipe, as this non-resonated pipe does not include one. If you are starting from scratch, you will need the full PLM mid pipe kit plus this conversion pipe.
The catalog does not specify gasket or clamp sizes. Reuse the hardware from your resonated section if it is in good condition, or consult PLM for replacement parts. No torque values or specific tool sizes are provided in the listing, so rely on standard exhaust installation practices and your kit's manual.


